Setting limits with ulimit

http://www.itworld.com/operating-systems/317369/setting-limits-ulimit?page=0,0


Administering Unix servers can be a challenge, especially when the systems you manage are heavily used and performance problems reduce availability. Fortunately, you can put limits on certain resources to help ensure that the most important processes on your servers can keep running and competing processes don't consume far more resources than is good for the overall system. The ulimit command can keep disaster at bay, but you need to anticipate where limits will make sense and where they will cause problems.
It may not happen all that often, but a single user who starts too many processes can make a system unusable for everyone else. A fork bomb -- a denial of service attack in which a process continually replicates itself until available resources are depleted -- is a worst case of this. However, even friendly users can use more resources than is good for a system -- often without intending to. At the same time, legitimate processes can sometimes fail when they are run against limits that are designed for average users. In this case, you need to make sure that these processes get beefed up allocations of system resources that will allow them to run properly without making the same resources available for everyone.
To see the limits associate with your login, use the command ulimit -a. If you're using a regular user account, you will likely see something like this:

$ ulimit -a
core file size          (blocks, -c) 0
data seg size           (kbytes, -d) unlimited
scheduling priority             (-e) 0
file size               (blocks, -f) unlimited
pending signals                 (-i) 32767
max locked memory       (kbytes, -l) 32
max memory size         (kbytes, -m) unlimited
open files                      (-n) 1024
pipe size            (512 bytes, -p) 8
POSIX message queues     (bytes, -q) 819200
real-time priority              (-r) 0
stack size              (kbytes, -s) 10240
cpu time               (seconds, -t) unlimited
max user processes              (-u) 50
virtual memory          (kbytes, -v) unlimited
file locks                      (-x) unlimited

One thing you might notice right off the bat is that you can't create core dumps -- because your max core file size is 0. Yes, that means nothing, no data, no core dump. If a process that you are running aborts, no core file is going to be dropped into your home directory. As long as the core file size is set to zero, core dumps are not allowed.


  This makes sense for most users since they probably wouldn't do anything more with a core dump other than erase it, but if you need a core dump to debug problems you are running into with an application, you might want to set your core file size to unlimited -- and maybe you can.

$ ulimit -c ulimited
$ ulimit -c
unlimited

If you are managing a server and want to turn on the ability to generate core dumps for all of your users -- perhaps they're developers are really need to be able to analyze these core dumps, you have to switch user to root and edit your /etc/security/limits.conf (Linux) or make changes in your /etc/system (Solaris) file.
If, on the other hand, you are managing a server and don't want any of your users able to generate core dumps regardless of how much they'd like to sink their teeth into one, you can set a limit of 0 in your limits.conf.
Another limit that is often enforced is one that limits the number of processes that an individual can run. The ulimit option used for this is -u. You can look at your limit as we did above with the ulimit -a command or show just the "nproc" limit with the command ulimit -u.

$ ulimit -u
50

Once again, your users can change their limits with another ulimit command -- ulimit -u 100 -- unless, of course, they can't. If you have limited them to 50 processes in the limits.conf or system file, they will get an error like this when they try to increase their limits:

$ ulimit -u 100
-bash: ulimit: max user processes: cannot modify limit: Operation not permitted

Limits can also be set up by group so that you can, say, give developers the ability to run more processes than managers. Lines like these in your limits.conf file would do that:

@managers          hard    nproc           50
@developers        hard    nproc          200

If you want to limit the number of open files, you just use a different setting.

@managers          hard    nofile         2048
@developers        hard    nofile         8192
sbob     hard    nofile   8192

Here we've given two groups and one individual increases in their open files limits. These all set hard limits. If you set soft limits as well, the users will get warnings when they reach the lower limit.

@developers        soft    nofile         2048
@developers        hard    nofile         8192

To see a list of the ulimit options, look at the man page (man ulimit).


  You will note that ulimit is a bash built-in -- at least on Linux -- and that the following options are available:

-a     All current limits are reported
-c     The maximum size of core files created
-d     The maximum size of a process's data segment
-e     The maximum scheduling priority ("nice")
-f     The  maximum  size  of files written by the shell and its
       children
-i     The maximum number of pending signals
-l     The maximum size that may be locked into memory
-m     The maximum resident set size (has no effect on Linux)
-n     The maximum number of open file descriptors (most systems
       do not allow this value to be set)
-p     The pipe size in 512-byte blocks (this may not be set)
-q     The maximum number of bytes in POSIX message queues
-r     The maximum real-time scheduling priority
-s     The maximum stack size
-t     The maximum amount of cpu time in seconds
-u     The  maximum  number  of  processes available to a single
       user
-v     The maximum amount of virtual  memory  available  to  the
       shell

If you limits.conf file permits, you might see limits like these set up for particular applications that really need the extra capacity. In this example, the oracle use is begin given the ability to run up to 16,384 processes and open 65,536 files. These lines would be set up in the oracle user's .bash_profile.

if [ $USER = "oracle" ]; then
  if [ $SHELL = "/bin/ksh" ]; then
    ulimit -p 16384
    ulimit -n 65536
  else
    ulimit -u 16384 -n 65536
  fi
fi

Setting limits can provide a defense against processes that go haywire and malicious processes that try to make your systems unusable. Just make sure that your limits work for you and not against you as you plan how your resources can best be allocated.

TERIMA KASIH ATAS KUNJUNGAN SAUDARA
Semoga artikel ini bermanfaat bagi saudara. Jika ingin mengutip, baik itu sebagian atau keseluruhan dari isi artikel ini harap menyertakan link dofollow ke https://androidblackberries.blogspot.com/2012/11/setting-limits-with-ulimit.html. Terima kasih sudah singgah membaca artikel ini.